Minoura CS-500 Instrukcja Użytkownika Pobierz pdf

iH-520-STD / iH-520-OS

instructions manual

(ver.1.0 2015/4)

2 different clamp sizes are available.

●

iH-520-STD : Fits 22 – 29mm diameter

●

iH-520-OS : Fits 27 – 35mm diameter

iH-520 Body

Side Hook (Small)

Plastic Shim (thin)

Plastic Shim (thick)

LW type

Clamp

Side Hook (Large) x2

iH-520 comes with the lightweight type clamp

which requires a tool to tighten.

Disassemble the clamp, wrap the

handlebar and shut the arms.

Insert the appropriate plastic shim

between the clamp and the handlebar

depending on the target tube diameter.

See the chart below;

[STD] [OS]

--------------------------------------------------

Thick Shim: 22mm / 27mm

Thin Shim: 25mm / 32mm

without Shim: 29mm / 35mm

Insert the roll nut in the all 3 holes.

Make sure the thread hole on the roller

nut can be seen through the hole beside

the clamp body.

Screw the bolt to the thread hole on the

roll nut.

Be sure you must screw the bolt with

your ngers for the rst 3 – 4 revolutions,

then use the 5mm hex wrench to x the

clamp securely.

Thin Shim Thick Shim

Be sure the roll nut is made of

soft alloy material. Do not force

to tighten, otherwise the thread

hole will be broken.

You should not use the hex

wrench from the beginning.

If the bolt has been slanted,

it will destroy the roll nut.

Silicon Ring

Variations

Side wings can be

locked to prevent

unexpected opening

from shock or

vibrations during ride.

Release

Neutral

Lock

Holds the phone

securely from all

4 directions.

The arms are

fully adjustable.

The side wings

open wide to

accommodate

devices up to

75mm wide, with

or without a case.

The included

white silicon ring

is a safety device

for holding the

phone together

with the holder in

order to prevent

unexpected

dropping off

problem.

Lower Arm

Fixing Screw

Lower Arm

Wing Lock &

Release Lever

Upper Arm

Side Hook

Locking Shim

Angle Adjust

Base

Upper Arm

Fixing Screw

Make sure you

securely lock

the wing before

start riding.

Functions

Do not push

the wings again

after locking.

This action will

automatically

release the

lock.

Silicon Ring Hook

Back Side

Check to make sure you have all the parts.

Contact place of purchase if you are missing

pieces.

Contents

Angle Adjust

Plate

3mm Hex Wrench

5mm Hex Wrench

M5x25 Flush Bolt

M5x16 Button Bolt

M5 Spring Waasher

Extended Lower Arm

Alloy Adapter

Install just above the clamp.

For mounting on the stem or for minimizing

the distance to you.

Install in front of the handlebar.

For locating the phone screen as far as

possible for easier view.

To open the wings, pull the red

wing release lever.

To clamp the phone, just push

the wings inward until they tightly

hold the phone.

After clamping, push down this

lever to lock the wings securely.

Do not push the wings

again after locking. This

will not tighten the wings

but will automatically

release the lock.

Installation – 1

Open / Close the Wings

1. Install the alloy adapter to the

clamp body rst by M5x16

button bolt and spring washer.

2. Put the holder body and the

angle adjust plate on the alloy

adapter. Insert the M5x25 ush

bolt through them and screw

to the clamp.

Holder body is angle adjust-able

in every 9 degrees.

You should need OS-size clamp

for mounting on the stem due to

the applicable diameter.

Place the holder body and

the angle adjust plate on the

clamp.

Pierce the M5x25 ush bolt

through them and screw to the

clamp.

Holder body is angle adjust-

able in every 9 degrees.

To adjust the angle, loosen the

ush bolt, lift up and turn the

holder.

After adjusting, tighten the

ush bolt rmly.

Clamp

Angle

Adust Plate

M5x25 Flush Bolt

Holder Body

Angle Adjust

Plate

Clamp

M5x16 Button bolt

M5 Spring

Washer

Alloy Adapter

M5x25

Flush Bolt

Using Silicon Ring

Embed the silicon ring to the backside hooks, and hold both the

holder and the phone in order to avoid unexpected dropping problem.

Installation – 2

To adjust the angle, loosen the ush bolt, lift up and turn the holder.

After adjusting, tighten the ush bolt rmly.

Always push the lock lever as the nal

step.

iH-520 comes with 2 sets of Side Hooks and

the smaller hooks are installed in standard.

Each hook can be set at 2 levels to t various

thickness of the phone case.

Choose the best hook size and position to

your actual phone size.

6 – 9mm Thick

12 – 15mm Thick

9 – 12mm Thick

15 – 18mm Thick

Small Hook / Low Large Hook / Low

Small Hook / High Large Hook / High

[ Default Combination ]

Side Hook (Small)

Side Hook (Large)

2 height levels available

Side Hook Locking

Shim

Insert the tip of

at screwdriver

and twist

While pushing the hook fully

toward the wing end, slide down

the shim to the pins to x.

Make sure you fully push down

the shim.

If the hook is slanted, the shim

cannot be installed.

Adjust Hook

Replace Lower Arm

If you are using an iPhone 6plus or

similar, you need to replace the the

lower arm with the extended arm if

your phone is longer than 147mm

(max. 173mm).

The arm is not position adjustable.

1. Loosen the backside lower

arm xing screw, and remove

the lower arm and the nut.

2. Replace the lower arm to the

extended one.

3. While sticking the extended

arm to the holder body, insert

the nut into the hole and

tighten the screw rmly.

Replace Hook

Extended

Lower Arm

Nut

Adjust the arm position to t the actual

phone size.

The center chrome plated

screw holds the arm. Loosen it

to adjust the arm position.

Do not loosen any

other screws.

Slide both arms until they

touch the phone case.

Tighten the backside screws

to x the position.

We recommend you set the

phone in the center of the

holder for the best t.

Slide the arms to make wide

space.

Adjust Arms

Put the phone on the holder

and close the wings to hold the

phone.

If the phone power

switch has been on or off

unexpectedly because the

wing pushes the button

when holding, add a piece

of pad (supplied) on the

existing pad on the side

hook.

Clamp Mechanism

1 2

Podsumowanie treści

Strona 1

iH-520-STD / iH-520-OS instructions manual(ver.1.0 2015/4)2 different clamp sizes are available.●iH-520-STD : Fits 22 – 29mm diameter●iH-520-OS : F

Strona 2

iH-520-STD / iH-520-OS　取扱説明書(ver.1.0 2015/4)モデルのちがいクランプの対応径ちがいで 2 種類あります。● iH-520-STD： 22 〜 29mm 径に対応します● iH-520-OS： 27 〜 35mm 径に対応しますパッケージ内容iH-520

Więcej dokumentów dla Dla rowerów MINOURA CS-500

Aby wyświetlić dokument Minoura CS-500 Instrukcja Użytkownika

Minoura CS-500 Instrukcja Użytkownika (3 strony)

Minoura CS-500 Instrukcja Użytkownika (2 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Minoura CS-500 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Dla rowerów Minoura CS-500. MINOURA CS-500 User Manual Instrukcja obsługi

Podsumowanie treści

Więcej dokumentów dla Dla rowerów MINOURA CS-500

Komentarze do niniejszej Instrukcji